Select Item 

Cube Moulds :IS 10086;516 | Beam Moulds | Cylender Moulds | Cylender Specimen Capping | Concrete Mixer | Jolting Apparatus

Preparation and Moulding
Methods of tests for strength of concrete require specimens for testing to be cast in a number of standard shapes and sizes for the compression and flexural, strength determination. These are called moulds.
The moulds are made of metal are stoutly built to minimize distortion and porosity and to retain their shape and size under rugged conditions.
Cube Moulds : IS 10086 ;416
Model No.
Description (Sizes)
Display
A 23.1
Cube size 50 X 50 X 50 mm
Click Here

Click Here
A 23.2
Cube size 70.6 X 70.6 X 70.6 mm
A 23.3
Cube size 100 X 100 X 100 mm
A 23.4
Cube size 150 X 150 X 150 mm
A 23.5
Cube size 200 X 200 X 200 mm
A 23.6
Cube size 300 X 300 X 300 mm
A 23.7
Cube size 600 X 600 X 600 mm
Beam Moulds : 10086; 516
Model No.
Description (Sizes)
Display
A 23.8
100 X 100 X 500 mm
  
A 23.9
150 X 150 X 700 mm
  
A 23.10
150 X 150 X 750 mm
  
A 23.11
40 X 40 X 160 mm
  
Cylinder Moulds : IS 10086
Moulds for casting concrete cylinders for compressive strength testing are of two sizes, these moulds are made of cast iron and split into two parts. These are supplied with base plate and meets specifications as per IS 516.
Model No.
Description (Sizes)
Display
A 23.12
150mm Dia X 300mm height
 Click Here

Click Here
A 23.13
100mm Dia X 200mm height
Cylindrical Specimen Capping
It is essential that the end of the concrete cylinder specimens are flat and parallel when conducting a compressive test, for this capping sets are available for use in the field as well as in the laboratory.
These are HORIZONTAL as well as VERTICLE type.
Horizontal Capping Set
Consists of a base on which two accurately machined plates are mounted.One plate is fixed and the other one is adjustable horizontally. Two plates are provided with holders for holding the cylinder in position. The holders are split horizontally.
Model No.
Description (Sizes)
Display
A 24.1
for capping test cylinders of 150mm dia X 300mm height
  
A 24.2
for capping test cylinders of 100mm dia X 200mm height
  
Vertical Capping Set
Consists of a base & an upright which serves as a guide for positioning the capping plate and the cylinder accurately machined capping plate is for keeping molten compound and to position the cylinder.
Model No.
Description (Sizes)
Display
A 24.3
for capping test cylinders of 150mm dia X 300mm height
 ssd
A 24.4
for capping test cylinders of 100mm dia X 200mm height
  
Model No.
Description (Sizes)
Display
A 25
Concrete Mixer ( Laboratory Models ) IS 179  
Concrete mixer laboratory type, electrically operated. Designed to remove the burden-some work of hand mixing. Uniform thoroughly mixed batches can be produced. The counter balanced drum is easy to tilt 1 1/2" to 2 cu.ft.mix. Mounted on a sturdy rubber tyre stand; the drum is mounted for end discharge & equipped with end towing pole.
 Click Here

Click Here
A 26
Jolting Apparatus  
The apparatus consists of a rectangular table rigidly connected by two support arms to a spindle at a horizontal distance of 800mm from the center of the table. The table can be raised and allowed to fall freely by a cam which is connected to a motor. The cam rotates at a rate of 60 rev/min. A stroke counter provided with micro switch is provided which stops the machine after 60 jolts. Locating pins are provided for mounting the mould compartments on the table. The mould surrounded by the hopper can be clamped rigidly to the table. Supplied complete with mould and hopper. Suitable for operation on 220 volts, 50 cycles, single phase A.C.
  



*NOTE : Specifications are subject to change without notice.